Mean Well EDR-75-24 DIN Rail 75W 24V Switching Power Supply

MODEL

EDR-75-24

OUTPUT

DC VOLTAGE

24V

RATED CURRENT

3.2A

CURRENT RANCE

0~3.2A

RATED POWER

76.8W

RIPPLE & NOSE (Max)   Note2

120mVp-p

VOLTAGE ADJ. RANGE  

24~28V

VOLTAGE TOLERANCE   Note3

±1.0%

LINE REGULATION

±0.5%

LOAD REGULATION

±1.0%

SETUP,RISE TIME         

1200ms, 60ms/230VAC 2000ms, 60ms/115VAC at full load

HOLD UP TIME (Typ.)

60ms/230VAC 12ms/115VAC at full load 

INPUT

VOLTAGE RANGE           Note6

90~264VAC 127~370VDC [DC input operation possible by connecting AC/L(+), AC/N(-)]

FREQUENCY RANGE

47 ~ 63Hz

POWER FACTOR (Typ.)

0.95/230VAC(400VAC) at full load

EFFICIENCY (Typ.)

87.5%

AC CURRENT (Typ.)

1.45A/115VAC   0.9A/230VAC

INRUSH CURRENT (Typ.)

20A/115VAC   35A/230VAC

LEAKAGE CURRENT

<1mA/240VAC

PROTECTION

OVERLOAD         

105 ~ 130% rated output power

Protection type: Constant current limiting, recovers automatically after fault condition is removed

OVER VOLTAGE

29~33V

Protection type: Shut down o/p voltage, re-power on to recover

OVER TEMPERATURE

Shut down o/p voltage, re-power on to recover

ENVIRONMENT

WORKING TEMP.

-20 ~ +60°C (Refer to “Derating Curve”)

WORKING HUMIDITY

20 ~ 95% RH non-condensing

STORAGE TEMP., HUMIDITY

-40 ~ +85°C, 10 ~ 95% RH

TEMP. COEFFICIENT

±0.03%/°C (0 ~ 50°C)

SAFETY

&

EMC

(Note 4)

VIBRATION

Component: 10 ~ 500Hz, 2G 10min./1 cycle, 60 min. each along X,Y,Z axes: Mounting: Compliance to IEC60068-2-6

SAFETY STANDARDS   

UL508, TUV EN60950-1 approved

WITHSTAND VOLTAGE

I/P-O/P: 3KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC 

ISOLATION RESISTANCE

I/P-O/P, I/P-FG, O/P-FG: >100M Ohms / 500VDC / 25°C / 70%RH

EMC EMISSION

Compliance to EN55022 (CISPR22) Class A,EN61000-3-2,-3

EMC IMMUNITY

Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024,EN61000-6-2(EN50082-2), heavy industry level, criteria A

OTHERS

MTBF

506.6K hrs min.   MIL-HDBK-217F(25°C)

DIMENSION

32*125.2*102mm (W*H*D)

PACKING

0.51Kg; 28pcs/15.3Kg/1.22CUFT

NOTE

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25°C of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12 “twisted pair-wire terminated with a 0.1uf &47uf parallel capacitor.
3. Tolerance: includes set up tolerance, line regulation and load regulation.
4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives.
5. Installation clearances: 40mm on top, 20mm on the bottom, 5mm on the left and right side are recommended when loaded permanently with full power. In case the adjacent device is heat source, 15mm clearance is recommended.
6. Derating may be needed under low input voltage. Please check the derating curve for more details.