Meanwell HLG-600H-54 600W LED Switching Power Supply

MODEL

HLG-600H-54

OUTPUT

DC VOLTAGE

54V

CONSTANT CURRENT REGION Note4

27~54V

RATED CURRENT

11.2A

RATED POWER

604.8W

RIPPLE&NOISE (Max)           Note2

350mVp-p

VOLTAGE ADJ. RANGE       Note6

45.9~56.7V

CURRENT ADJ. RANGE

Can be adjusted by internal potentiometer A type only

5.6~11.2A

VOLTAGE TOLERANCE       Note3

±1.0%

LINE REGULATION

±0.5%

LOAD REGULATION

±0.5%

SETUP,RISE TIME                Note.8

500ms,80ms at full load  230VAC/115VAC

HOLD UP TIME (Typ.)

15ms at full load  230VAC/115VAC

INPUT

VOLTAGE RANGE               Note.5

90~305VAC 127~431VDC

FREQUENCY RANGE

47 ~ 63Hz

POWER FACTOR (Typ.)

PF>0.98/115VAC, PF>0.96/230VAC. PF>0.93/277VAC at full load (Please refer to “Power Factor Characteristic” curve)

TOTAL HARMONIC DISTORTION

THD<20% when output loading≥50% at115VAC/230VAC input and output loading≥75% at 277VAC input

EFFICIENCY (Typ.)

230VAC

96%

277VAC

96%

AC CURRENT (Typ.)

7A/115VAC  3.3A/230VAC 2.9A/277VAC

INRUSH CURRENT (Typ.)

COLD START 70A (twidth=1000μs measured at 50% lpeak) at 230VAC

LEAKAGE CURRENT

<0.75mA/277VAC

PROTECTION

OVER CURRENT                     Note.4

95 ~ 108%

Protection type: Constant current limiting, recovers automatically after fault condition is removed

SHORT CIRCUIT

Constant current limiting, recovers automatically after fault condition is removed

OVER VOLTAGE

46~50V

Protection type: Shut down, re-power on to recovery

OVER TEMPERATURE

Shut down o/p voltage, re-power on to recover

FUNCTION

REMOTE ON/OFF CONTROL

Power on:”Hi”>2~5V or(Open circuit) Power off: “LOW”<0~0.5V or (Short circuit)

5V STANDBY

5VSB:5V 0.5A:tolerance±5%, ripple: 100mVp-p (max.)

ENVIRONMENT

WORKING TEMP.

-40 ~ +70°C (Refer to “Derating Curve”)

WORKING HUMIDITY

20 ~ 95% RH non-condensing

STORAGE TEMP., HUMIDITY

-40 ~ +80°C, 10 ~ 95% RH

TEMP. COEFFICIENT

±0.03%/°C (0 ~ 60°C)

VIBRATION

10 ~ 500Hz, 5G 12min./1 cycle, period for 72min. each along X,Y,Z axes

SAFETY

&

EMC

SAFETY STANDARDS            Note7

UL8750, CSAC22.2 No.250.13-12,EN61347-1,EN61347-2-13 independent IP65 or IP67 approved

WITHSTAND VOLTAGE

I/P-O/P: 3.75KVAC  I/P-FG:2KVAC O/P-FG:0.5KVAC

ISOLATION RESISTANCE

I/P-O/P, I/P-FG, O/P-FG: 100M Ohms / 500VDC / 25°C / 70%RH

EMC EMISSION

Compliance to EN55015, EN55022(CISPR22) Class B, EN61000-3-2 Class C (≥50% load) ; EN61000-3-3

EMC IMMUNITY

Compliance to EN61000-4-2,3,4,5,6,8,11, EN61547, EN55024, light industry level (surge 4KV), criteria A

OTHERS

MTBF

76.9K hrs min.   MIL-HDBK-217F(25°C)

DIMENSION

280*144*48.5mm (L*W*H)

PACKING

3.9Kg; 4pcs/16.6Kg/0.9CUFT

NOTE

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25°C of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12 “twisted pair-wire terminated with a 0.1uf &47uf parallel capacitor.
3. Tolerance: includes set up tolerance, line regulation and load regulation.
4. Constant current operation region is within 50%~100% rated output voltage. This is the suitable operation region for LED related application, but please reconfirm special electrical requirements for some special system design.
5. Derating may be needed under low input voltages. Please check the static characteristics for more details.
6. A type only.
7. Safety and EMC design refer to EN60598-1, subject CNS15233, GB7000.1, FCC part18.
8. Length of set up time is measured at cold first start. Turning ON/OFF the power supply may lead to increase of the set up time.
9. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-quality EMC. Directive on the complete installation again.
10. Refer to warranty statement.